PCK0J821MCO1GS【PDF 1/2 页】CAP ALUM 820UF 6.3V 20% SMD

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录872

[1页]2页

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Chip Type, Ultra-low ESR

series

Ultra-low ESR, Higher Capacitance, High ripple current.

Load life of 2000 hours at 105 ° C.

SMD type : Lead free reflow soldering condition at 260 ° C peak

correspondence.

Compliant to the RoHS directive (2011/65/EU).

Specifications

Low ESR

Item

Category Temperature Range

Rated Voltage Range

– 55 to +105 ° C

2.5 to 6.3V

Performance Characteristics

Rated Capacitance Range 220 to 2200μF

Capacitance Tolerance

± 20% at 120Hz, 20 ° C

Tangent of loss angle (tan δ ) Less than or equal to the specified value at 120Hz, 20 ° C

ESR (

Less than or equal to the specified value at 100kHz, 20 ° C

Leakage Current (

Less than or equal to the specified value .

After 2 minutes' application of rated voltage at 20 ° C

Temperature Characteristics

(Max.Impedance Ratio)

Z+105 ° C / Z+20 ° C

Z – 55 ° C / Z+20 ° C

1.25

(100kHz)

Endurance

Damp Heat

(Steady State)

The specifications listed at right shall be met when the

capacitors are restored to 20 ° C after the rated voltage is

applied for 2000 hours at 105 ° C.

The specifications listed at right shall be met when the

capacitors are restored to 20 ° C after the rated voltage is

applied for 1000 hours at 60 ° C, 90% RH.

Capacitance change

tan δ

ESR ( 1)

Leakage current ( 2)

Capacitance change

tan δ

ESR ( 1)

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

Less than or equal to the initial specified value

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

Less than or equal to the initial specified value

After soldering the capacitor under the soldering conditions

Resistance to

Soldering Heat

prescribed here, the capacitor shall meet the specifications listed at

right, provided that it's temperature profile is measured at the

capacitor top and the terminal.

Pre-heating shall be done at 150 to 200 ° C and for 60 to 180 sec.

The duration for over +230 ° C temperature at capacitor surface shall

not exceed 60 seconds.

In the case of peak temp, less than 250 ° C, reflow soldering shall be

Capacitance change

tan δ

ESR ( 1)

Leakage current ( 2)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

Less than or equal to the initial specified value

two times maximum.

In the case of peak temp, less than 260 ° C, reflow soldering shall be

once.

Measurement for solder temperature profile shall be made at the

capacitor top and the terminal.

Marking

Navy blue print on the case top

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105 ° C.

3 Initial value : The value before test of examination of resistance to soldering.

Dimensions

Positive

Type numbering system (Example : 6.3V 220μF)

Plastic platform

9 10 11 12 13 14

Capacitance

Lot No.

0.3 MAX.

C ± 0.2

P C K 0 J 2 2 1 M C O 1 G S

Taping code

Configuration

Capacitance tolerance ( ± 20%)

Series

Voltage ( j:6.3v)

- 0.4

L +0.1

Negative

Rated capacitance (220 μ F)

(mm)

Rated voltage (6.3V)

Series name

Type

Size

φ 6.3 × 6L

φ 8 × 7L

φ 10 × 8L φ 10 × 10L

φ D

6.3

5.9

7.3

8.0

6.9

9.0

10.0

7.9

11.0

10.0

9.9

11.0

6.6

8.3

10.3

Voltage

6.6

2.1

8.3

3.2

10.3

4.6

10.3

4.6

2.5

6.3

0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1

Code

Dimension table in next page.

CAT.8100C

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式